hardware:3dprinters
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| hardware:3dprinters [2019/02/07 12:18] – [3D Printers @ IAI] amaldo | hardware:3dprinters [2019/02/07 14:22] (current) – [Ultimaker 2] amaldo | ||
|---|---|---|---|
| Line 14: | Line 14: | ||
| Installed updates: | Installed updates: | ||
| - | * Olsson block: Not an actual Olsson block, but a newer improved version made by 3Dsolex (Norway): [[http:// | + | * Original |
| - | * Extruder: [[http:// | + | |
| - | * Feeder exchanged by the [[https:// | + | |
| - | * MK8 gear feeder. This replaces the knurled feeder gear from the original Ultimaker feeder. More info [[http:// | + | |
| * 3dSolex 35W block heater | * 3dSolex 35W block heater | ||
| + | * [[https:// | ||
| * 3dSolex pt100 temperature sensor (the original one broke while taking it out of the original block) | * 3dSolex pt100 temperature sensor (the original one broke while taking it out of the original block) | ||
| - | * Fan shroud: [[https:// | + | * Fan shroud: [[https:// |
| * Low friction Spool holder. [[https:// | * Low friction Spool holder. [[https:// | ||
| * Firmware: TinkerGnome V17.10.1 | * Firmware: TinkerGnome V17.10.1 | ||
| - | * Current of E Axis motor was increased | + | * Current of E Axis motor was decreased |
| * Last good z-offset to buildplate: 19.15mm (with this height the first layer is 0.3mm +-0.02 and the feeder does not miss steps while extruding the first layer, close to perfect). This height will change if the extruder tip is changed or the springs under the heated bed are adjusted. | * Last good z-offset to buildplate: 19.15mm (with this height the first layer is 0.3mm +-0.02 and the feeder does not miss steps while extruding the first layer, close to perfect). This height will change if the extruder tip is changed or the springs under the heated bed are adjusted. | ||
| Line 35: | Line 33: | ||
| * Olsson block: The original Olsson block for 2.85mm diameter filament (same one as in the UM2+) | * Olsson block: The original Olsson block for 2.85mm diameter filament (same one as in the UM2+) | ||
| * Extruder: 0.4mm brass extruder. Exchangeable for other sizes. | * Extruder: 0.4mm brass extruder. Exchangeable for other sizes. | ||
| - | * Feeder exchanged by the [[https:// | + | * [[https:// |
| - | * MK8 gear feeder. This replaces the knurled feeder gear from the original Ultimaker feeder. More info [[http:// | + | |
| * block heather: Original 25W heater. (A new 3dSolex 35W block heater could be installed). | * block heather: Original 25W heater. (A new 3dSolex 35W block heater could be installed). | ||
| * 3dSolex pt100 temperature sensor (the original one broke while taking it out of the original block) | * 3dSolex pt100 temperature sensor (the original one broke while taking it out of the original block) | ||
| Line 42: | Line 39: | ||
| * Low friction Spool holder. [[https:// | * Low friction Spool holder. [[https:// | ||
| * Firmware: TinkerGnome V17.10.1 | * Firmware: TinkerGnome V17.10.1 | ||
| - | * Current of E Axis motor was increased | + | * Current of E Axis motor was decreased |
| * Fix: The Printer reported often an error on the temperature sensor of the heatbed. The cable connector on the heatbed was not soldered properly from the factory, making the pins have an intermittent connection. Alexis soldered them again and it got rid of the errors. | * Fix: The Printer reported often an error on the temperature sensor of the heatbed. The cable connector on the heatbed was not soldered properly from the factory, making the pins have an intermittent connection. Alexis soldered them again and it got rid of the errors. | ||
| * Door: official transparent front door. | * Door: official transparent front door. | ||
hardware/3dprinters.1549541882.txt.gz · Last modified: 2019/02/07 12:18 by amaldo